PLANT

Benefits of soft starters for electric motors


Sponsored Content provided by PLANT partners:

Soft starters from eMotors.
Photo: eMotors.

They relieve stress that drives up costs and reduces productivity

In electric motor applications, it is important to avoid situations that create unnecessary wear and tear on the motor and driven machinery. This can result in reduced service life, significant replacement and maintenance costs, and loss of productivity.

One of the most critical parts of the operation is at start-up, where a variety of factors combine to dramatically increase the stress on the motor and the infrastructure that it’s connected to. However, by utilizing a soft starter, this stress can be almost completely avoided.

When full power is supplied to an AC induction motor at standstill, the motor can draw an initial current of more than seven times the normal load current, before dropping back down as it approaches full speed. During this time, the motor and electrical system experience abnormally high currents, which result in potentially damaging heat stress. It also creates a requirement for oversized cables and components, and may incur significant extra costs from electricity supply companies who determine rates according to peak current demand.

Additionally, with full power applied, the motor will attempt to accelerate very quickly, producing up to three times the normal load torque. Especially with large, powerful motors, this can cause mechanical shock to the motor, drivetrain and the driven load, with potential consequences including:

  • Worn or failed bearings
  • Belt drive slipping
  • Gearbox and drivetrain wear and damage
  • Water hammer in pumping systems
  • Damage to driven machinery.

To deal with these problems, install a soft starter that gradually increases the voltage supplied to a motor when it is started, preventing the current and torque from building up too quickly. In a typical AC induction motor, the current drawn by the motor is proportional to the square of the supply voltage, and the torque is proportional to the current. This means ramping up the voltage slowly results in a smooth build-up of current and torque in the motor.

In the common configuration, a soft starter consists of two thyristors – or SCRs as they are commonly known – connected back-to-back for each phase, which work together to control the voltage supplied to the motor. Because AC voltage is rapidly changing between positive and negative at the line frequency, the supply voltage is controlled by switching the power on and off during specific parts of the AC voltage waveform. Thyristors operate like electrical switches, making them ideal for this task.

Soft starters include a logic controller that determines the timing of power supply to the motor, and this can be open loop or closed loop. Open loop devices do not have a feedback system – they do not modify their output based on the behaviour of the motor, instead ramping up the voltage according to a pre-selected set of values. Closed-loop devices monitor the current build-up in the motor with a feedback loop, allowing them to closely manage the start-up of the motor for maximum efficiency.

A variable frequency drive (VFD) controls the speed of a motor by modifying the frequency of the AC supply power. While used primarily for precision speed control, a VFD is also used as a soft starter, and is best suited for applications where the acceleration characteristics must be highly consistent even with variable loads. However, VFDs have some downsides: they’re expensive and require the management of potential bearing currents.

When using soft starters, however, the load on the motor impacts how fast it will accelerate. If the main concern is simply to limit the current surge in the motor rather than achieve a precise acceleration time, a soft starter is a more cost-effective choice, especially in large, high-power applications.

The initial voltage supplied by a soft starter has a significant impact on how effective it is. Especially when connected to a high-inertia load, a motor may require a substantial amount of torque to begin rotating. When insufficient power is supplied to create rotation, heat builds in the windings and quickly reaches damaging levels. Therefore, it’s important to choose an initial voltage that’s high enough to get the motor rotating straight away – ideally within one to two seconds of energization.

The ramp time is how long the soft starter takes to go from starting voltage to full line voltage. A longer ramp time reduces the torque in the motor during start-up, resulting in a slower, smoother acceleration, and is common for applications such as water pumps and conveyors where the infrastructure that the motor is connected to is at greater risk from mechanical shock.

For applications where the load on the motor during start-up varies considerably, use a soft starter that monitors the current in the motor to prevent excessive current surges in the system when the load is high.

Applying full power to a motor at start-up often results in mechanical and electrodynamic stress on the motor, electrical system, and connected machinery that reduces service life and increases costs. By utilizing a soft starter, this problem can be avoided, maximizing the productivity and operational efficiency of the application.

eMotors Direct carries a full line up of electronic soft starters in its 30 warehouses across Canada, including popular brands such as ABB, WEG and Motortronics.

William Schrottky is a technical writer at eMotors Direct Inc., an online supplier of electric motors, parts and accessories based in Edmonton. For information about soft starters for electric motors, visit https://www.emotorsdirect.ca.