PLANT


Technology Centre

Tech Centre Manufacturing Operations Production Technology
January 31, 2017  

I/O module supports IIoT

Range of input and output types.

Tech Centre Manufacturing Operations Production Technology
January 31, 2017  

Lever hoists improve operator safety

Handle rotates 360-degrees.

Tech Centre Manufacturing Operations Production Technology
January 31, 2017  

Valves, manifolds operate in sync

3, 5, 12 or 24 VDC coils.

Tech Centre Manufacturing Operations Technology
January 31, 2017  

Mill increases tool life by 50%

Low vibration susceptibility.

Tech Centre Manufacturing General Technology
February 26, 2016  

Exchangers reduce film build up

Process fluid is continuously pushed from the centre of each tube to the wall and back, eliminating thermal gradients.

Tech Centre Manufacturing General Technology
February 24, 2016  

Robot is fast, cuts cycle times

A reliable counterweight and mechanical springs counter balance the robot to shorten cycle times and improve accuracy.

Tech Centre Manufacturing General Technology
February 23, 2016  

Stop switches reduce machinery damage

Fitted with 22.5-mm mounting actuators that illuminate and are impact, vibration and shock resistant.

Tech Centre Manufacturing General Technology
February 21, 2016  

Pumps enhance energy savings

Equipped with TEFC motors as standard to 25 hp and come in 230, 460 or 575 V options.

Tech Centre Manufacturing General Technology
February 20, 2016  

Uncover undiagnosed loop problems

An internal power supply drives the loop while finding ground faults and leakage current caused by corrosion or condensation.

Tech Centre Manufacturing General Operations Technology
February 19, 2016  

Studs install in metal sheets as thin as 1 mm

Studs mount flush in the metal sheet for a clean and more attractive finished appearance

Tech Centre Manufacturing General Technology
February 17, 2016  

Proxswitch’s pulse output to 120 VAC/VDC

Sensors detect shaft, gate or slide position as well as object presence.

Tech Centre Manufacturing General Operations Technology
February 17, 2016  

Suction cups improve productivity

A single bellow stays more stable when in motion, allowing robots or production lines to run at higher speeds.

Tech Centre Manufacturing General Operations Technology
February 17, 2016  

Photoelectrics set for tough environments

Fitted with 316L stainless steel housings for food and beverage applications.

Tech Centre Manufacturing General Technology
February 16, 2016  

Measure high laser powers without water cooling

Laser irradiates the sensor for a short time, from 0.1 to 1 s, and the energy of the pulse is used to calculate the power.

Tech Centre Manufacturing General Technology
February 16, 2016  

Data acquisition in Industry 4.0

Slave ethernet port links up to eight daisy-chained expansion modules and converts more than 100 channels to one IP address.

Tech Centre Manufacturing General Technology
February 16, 2016  

Carts keep shop valuables secure

Built with a welded steel frame, tubular steel push handle, steel-reinforced butcher block work surface.

Tech Centre Manufacturing General Operations Technology
February 15, 2016  

Sensorless control for pumping systems

IPS 4000 operates in either a stand-alone mode or networked through the BMS to maximize performance.

Tech Centre Manufacturing General Technology
February 12, 2016  

High-temperature ovens ease welding

Workspace floor is reinforced for 3,000 lb. loading at removable subway grate.

Tech Centre Manufacturing General Technology
December 23, 2015  

Machine verification in real time

Complies with insurance audits and OSHA 29 CFR 1910.272 requirements.

Tech Centre Manufacturing General Technology
December 23, 2015  

BOA2 detects smaller defects

Sensor supports standard C-mount lenses to safeguard against accidental damage or tampering.

Tech Centre Manufacturing General Technology
December 22, 2015  

Pumps pass large solids easily

Flap valves prevent damage from product entrapment and settling of solids in intermittent-duty applications.

Tech Centre Manufacturing General Technology
December 21, 2015  

Pumps handle non-corrosive water conditions

Come in five sizes for diameters from 150 to 350 mm.

Tech Centre Manufacturing General Technology
December 19, 2015  

Imager captures thermal anomolies

32-times electronic zoom, and the still or video images are stored via microSD or USB2.0.

Tech Centre Manufacturing General Technology
December 16, 2015  

Connectors handle high vibrations, shock loads

Rated at 4 A per contact and 250 V.

Tech Centre Manufacturing General Technology
December 15, 2015  

ECO-HEAT maximizes diesel engine performance

Raises the engine load and heats the exhaust directly to save space and energy.

Tech Centre Manufacturing General Technology
December 14, 2015  

Converters fit in tight spaces

Eighteen models operate with 3.3, 5, 12, 15 and 24 VDC inputs and single outputs.

Tech Centre Manufacturing General Technology
December 13, 2015  

Prep surfaces with precision

Rear vestibule accommodates full movement of the pressure-blast lance.

Tech Centre Manufacturing General Technology
December 11, 2015  

Super fast pick and place

Multiple programming interfaces allows developers to work in an environment that matches their skill sets or application requirements.

Tech Centre Manufacturing General Technology
December 10, 2015  

Input modules digitize strain gauge signals

Compensation in the measurement system eliminates absolute uncertainty in the measurement circuit.

Tech Centre Manufacturing General Technology
December 9, 2015  

Safe robotic cable retraction without looping

Retraction stroke of up to 23.6 in.

Tech Centre Manufacturing General Technology
December 8, 2015  

Turn up the machining volume

Driven by servo motors to save on energy and maintenance costs.

Tech Centre Manufacturing General Technology
December 7, 2015  

Automated palletizers get an upgrade

Guards are easy to handle and remove for quick access to components.